DrivePro® Start-up gives the Customer a full range of checks and
adjustments during commissioning of the drive, ensuring their system is
tuned for optimal performance right from day one.
The following benefits can be gained:
• Installation is checked to ensure it complies to Danfoss guide
lines.
• The AC drive is fine-tuned specific to the application, ensuring
optimal performance.
• Maximum energy savings to the Customer.
• Extend the AC drive’s lifespan.
• Report detailing findings.
Before DrivePro® Start-up can be implemented, the AC drive must be
installed and
ready for operation. The entire system must be fully operational under
normal operation conditions. Installation of the drive is not included
in this package. Commissioning needs to take place during the standard
working hours.
DrivePro® Start-up includes 1 engineer for 3 working days for each MV
Drive in case of site readiness. Prolonging of the job caused by reasons
not caused by Danfoss Drives will result in additional costs to the
customer.
Travelling costs will be invoiced based on real expenses +10% handling
fee.
General Terms and Conditions of Delivery and Warranty apply.

DrivePro® Start-up gives the Customer a full range of checks and
adjustments during commissioning of the drive, ensuring their system is
tuned for optimal performance right from day one.
The following benefits can be gained:
• Installation is checked to ensure it complies to Danfoss guide
lines.
• The AC drive is fine-tuned specific to the application, ensuring
optimal performance.
• Maximum energy savings to the Customer.
• Extend the AC drive’s lifespan.
• Report detailing findings.
Before DrivePro® Start-up can be implemented, the AC drive must be
installed and
ready for operation. The entire system must be fully operational under
normal operation conditions. Installation of the drive is not included
in this package. Commissioning needs to take place during the standard
working hours.
DrivePro® Start-up includes 1 engineer for 3 working days for each MV
Drive in case of site readiness. Prolonging of the job caused by reasons
not caused by Danfoss Drives will result in additional costs to the
customer.
Travelling costs will be invoiced based on real expenses +10% handling
fee.
General Terms and Conditions of Delivery and Warranty apply.

TWO-PHASE FROST PROTECTION THERMOSTATS FS-20-UW
Electronic frost protection thermostat or frost monitor with switching
relay output, continuous temperature and valve output (summation output
0–10 V) and control and cascading output (0–10 V), optionally with
connection for a heating element. A IP65 resistant plastic housing with
display with the actual temperature, measuring range,
overrange/underrange of the set switch point (frost protection
temperature) and alarm indicator for "frost" or "error" (capillary
breakage, overvoltage/undervoltage), quick-locking screws and a fully
active sensor rod made of copper. The delivery scope includes a set of
MK-05-K mounting clamps for expert attachment of the sensor rod.
Measuring range: 0...+15 °C / 32...+59 °F
Accuracy: typical ± 1 K (at +10 °C)
Sensor type: 3m Copper rod active along the entire sensor length, min.
response length of 25 cm
Input: 1 x 0 -10 V control input DDC & 1 x 0 -10 V ascading input
Output: 1 x 0 -10 V output temperature (corresponding to 0...+15 °C) &
1 x 0 -10 V output valve (frost signal with control voltage and
cascading)
1 x potential-free changeover contact (24 V), range of adjustment 0...+
15 °C
Current consumption: max. 100 mA at 24 V DC
Load resistance: RL > 50 kOhm
Ambient temperature: –15...+50 °C / 5...+122 °F (Housing) & –20...+60 °C
/ -4...+140 °F Sensor and capillary tube > 20 cm from the housing.
Power: 24VAC/DC (± 10%) 24DC <2,4W
T2-IP65 plastic housing with three-line display 70x40 mm (WxH), a M16
cable glands and MK-05-K mounting clamps.
Housing dimensions: 126 x 90 x 50 mm / 4.96 x 3.54 x 1.97 in

Opening Tools MCD 600 in case of service.
Tool consist of two parts to be used at top an bottom to release locks